Sungrow SBH200

Official manufacturer EU/global перевірено 20 вересня 2026 р.

Невирішений конфлікт щодо безпеки
Два джерела подають різні значення для цього продукту, і ніхто цього не вирішив. Характеристики нижче показано так, як їх записано, але цей продукт не можна вважати перевіреним для інженерних цілей, доки конфлікт не закрито.

Sungrow SBH200 — PRODUCT PHOTO · Sungrow
UNKNOWN

Identity

category	batteries
ean	—
generation	SBH (stackable high-voltage)
hardware_revision	—
legacy_name	—
manufacturer	Sungrow
market_version	IEC datasheet V4 (2024-03-29)
model	SBH200
mpn	—
note	SBH100 and SBH150 are marked 'not available for sale in Australia' (user manual p.8)
product_family	SBH100 / 150 / 200 / 250 / 300 / 350 / 400
product_revision	V11 (standard) and V12 (with heating)
product_status	active
product_status_evidence	Carried with full specifications in Sungrow Compatibility List PUBLIC 2026 V4.3 dated 01.06.2026
region	EU/global
release_year	2024
sku	—
subcategory	residential high-voltage stacked battery system
variant_note	One of seven fixed stack configurations of the same 5.0 kWh module; differs from siblings only by module count.

Electrical

architecture	HV (high-voltage DC series stack)
cell_chemistry	LiFePO4 Prismatic Cell
chemistry	LFP (LiFePO4 prismatic cell)
communication_can	True
communication_rs485	—
expansion_rules	Compatibility List V4.3: SH5.0-10RT accepts 'SBH150-400 3 to 8 modules ... max 1 tower' (V112 and -20 versions only); SH5.0-25T accepts 'SBH100-400 2 to 8 modules ... max 2 towers with Y connector; power limited by battery'. Y-connector note: '2 battery towers in parallel (same capacity up to 80 kWh)'.
firmware_requirements	User manual p.54: 'For the European region, SBH series is only applicable to SHT series inverters and the version should be later than PEARL-H_01011.01.21.' and 'The inverter model should be SH3.0-6.0RS/SH8.0-10.0RS series and the version should be later than SUNSTONE-H_01011.02.43(LCD)/SUNSTONE-H_01011.02.40(LCD).'
max_charge_current_a	50
max_charge_power_kw	—
max_continuous_charge_current_a	50 SBH100/150/200/250/300/350/400 Datasheet V4 EN — 'Max. continuous charge/discharge current 50 A' (family-wide)
max_continuous_discharge_current_a	50
max_continuous_power_kw	—
max_discharge_current_a	50
max_discharge_power_kw	—
max_parallel_stacks	—
max_parallel_units	4
max_series_units	8
min_series_units_hv	2
mixed_generation_restrictions	—
modules_installed	4
modules_max	8
modules_min	2
nominal_energy_kwh	20.0
nominal_voltage_v	281.6 SBH100/150/200/250/300/350/400 Datasheet V4 EN — spec table, SBH200 column, 'Nominal voltage 281.6 V'
officially_supported_inverter_brands	['Sungrow']
officially_supported_inverter_models	["SH5T / SH6T / SH8T / SH10T / SH12T / SH15T / SH20T / SH25T (EU: 'SBH100-400 battery is only compatible with SH5-25T inverter')", 'SH3.0RS / SH3.6RS / SH4.0RS / SH5.0RS / SH6.0RS / SH8.0RS / SH10RS (per user manual p.54, with firmware condition)'] High Voltage LFP Battery User Manual (SBH series) — p.45 and p.54
operating_voltage_max_v	321.2
operating_voltage_min_v	237.6
peak_current_a	—
power_note	Only a continuous current (50 A) is printed. No kW figure printed; not derived.
rated_power_kw	—
round_trip_efficiency_pct	—
short_circuit_current_a	—
short_circuit_note	NOT printed on SBH datasheet V4. The SBR series' 3500 A figure was deliberately NOT carried over.
supported_inverter_protocols	['CAN']
usable_dod_note	'Max. 100% DOD (settable)'
usable_dod_pct	100
usable_energy_kwh	20.0 (max 100 % DoD, settable)
usable_energy_note	Datasheet row label is 'Useable Energy'; DOD row is 'Max. 100% DOD (settable)'.
voltage_class	HV
voltage_range_v	237.6-321.2 (SBH200 / 4 PACKs). Family: each PACK is 5.0 kWh / 70.4 V nominal; SBH100 (2 PACKs) to SBH400 (8 PACKs) scale the window proportionally SBH100/150/200/250/300/350/400 Datasheet V4 EN — spec table, SBH200 column, 'Operating voltage range 237.6V-321.2V'

Physical / mechanical

base_dimensions_mm	650 +/- 5 x 55 +/- 5 x 325 +/- 5
base_weight_kg	2.5 +/- 1
cable_entry_positions	—
cooling	Natural convection
depth_mm	350
dimensions_note	Datasheet row 'Dimensions (W x H x D)'
display	SOC indicator, Status indicator
height_mm	900
ip_rating	IP55
module_dimensions_mm	675 +/- 5 x 160 +/- 5 x 350 +/- 5 (handles/connectors excluded)
module_energy_kwh	5.0
module_weight_kg	45 +/- 2 (V11); 46 +/- 2 (V12) суперечливе
mounting	Floor stand
mounting_type	['floor', 'wall']
shipping_weight_kg	—
stack_dimensions_by_size_mm	SBH100 (2 PACKs) 675x580x350; SBH200 (4) 675x900x350; SBH400 (8) 675x1540x350
stack_weight_by_size_kg	SBH100 106 (V11) / 108 (V12); SBH400 376 (V11) / 384 (V12)
terminal_locations	switch gear at the top of the stack
torque_specs	—
weight_kg	196
width_mm	675

Installation

clearance_front_mm	—
clearance_left_mm	—
clearance_rear_mm	42-62 (distance from the wall)
clearance_right_mm	—
clearance_top_mm	—
indoor_outdoor	indoor and outdoor (IP55)
inverter_phase_module_limits	'SUNGROW single-phase hybrid inverter used with battery system consisting of 2~6 PACKs; SUNGROW three-phase hybrid inverter used with battery system consisting of 3~8 PACKs' (user manual p.64)
max_installation_altitude_m	2000
maximum_modules_per_stack	8
maximum_stacks_in_parallel	4 High Voltage LFP Battery User Manual (SBH series) — p.45
minimum_modules_per_stack	2
mounting_method	Floor stand
mounting_orientation	upright stack on a floor stand base; wall-mounting also supported
orientation_allowed	['floor stand', 'wall-mounted']
parallel_rules	'RACKs (battery systems) can be connected in parallel, allowing for at most 4 RACKs to be cascaded' and 'Please make sure the usable energy of each RACK is the same when cascading.' 'The SBH-V12 version currently supports single-cluster battery configurations only.'
seismic_anchoring	battery fixing brackets specified; no seismic load rating published
supported_installation_topology	—
surface_requirements	'The support structure ... should be fireproof and not made of flammable materials. Please make sure the support structure is solid enough to hold the device.' Battery fixing brackets required.
two_person_lift_required	—
ventilation_requirements	'Reserve enough clearance around the battery to ensure sufficient space for heat dissipation'

Environment

altitude_note	SBH is rated 'Max. 2000 m' - LOWER than the SBR series' 4000 m. Not a transcription error; both were read from their own datasheets.
charge_temperature_c	0 to +50 (V11); -20 to +50 (V12 heating version) суперечливе
cooling_method	natural convection
discharge_temperature_c	-20 to +50
fan_replaceable	—
humidity	0% - 95% no condensing
ik_rating	—
max_altitude_m	2000
nema_rating	—
noise	—
noise_level_db	—
operating_temperature_c	charge 0 to +50 (V11) or -20 to +50 (V12 with heating); discharge -20 to +50
relative_humidity	0-95 % non-condensing (datasheet); 5-95 % non-condensing (manual)
storage_temperature_c	ideal +15 to +25; acceptable -10 to +35; storage <= 6 months, maximum 12 months
temperature_note	Charge and discharge windows DIFFER; rows read 'Charge Temperature 0C - 50C' and 'Discharge Temperature -20C - 50C'.

Interfaces & connectors

battery_terminal_type	power connector with swivel nut, cold-pressed terminals; DC cable 10 mm2 (7 AWG), outer diameter 6-9 mm, multi-core PV cable rated > 1100 V
can	yes - two ports, 'IN is used for connecting the termination resistor, while OUT for the hybrid inverter' суперечливе
communication_protocol	CAN (to Sungrow hybrid inverter)
ethernet	no (RJ45 connector is used for the CAN link)
grounding	outdoor multi-core copper cable 10-16 mm2 (7-5 AWG), 1000 V, 105 C
ports	—
protocol_notes	communication cable is a Cat5e shielded network cable supplied as an accessory; RJ45 on the battery side, cold-pressed CAN1_H / CAN1_L terminals on the inverter side; termination resistor required
rs485	—

Controls & display

audible_alarm	—
buttons	black start button
display_type	—
leds	—
local_display	False
mobile_app	iSolarCloud

Protection

dc_breaker	True
fire_suppression	integrated per-module fire suppression kit
integrated_breakers_fuses	DC circuit breaker integrated in the switch gear
integrated_dc_switch	True
over_current	yes
over_current_protection	True
over_temperature	yes - over/under temperature protection with system shutdown outside the operating window
over_under_temperature_protection	True
over_under_voltage_protection	True
over_voltage	yes
short_circuit	yes - DC circuit breaker in the switch gear provides short-circuit protection
thermal_runaway_measures	'Fire suppression kit is integrated into the module and is triggered in case of emergency'; explosion relief valve present High Voltage LFP Battery User Manual (SBH series) — safety chapter, integrated fire suppression kit
under_voltage	yes

Certifications

emc	[]
grid_codes	['VDE 2510-50']
listed	['CE', 'CEC', 'IEC 62619', 'IEC 62040', 'UN 38.3', 'VDE 2510-50', 'IEC 62477', 'IEC 63056']
other	['UN 38.3']
regional	['CE', 'CEC', 'TUV', 'UKCA']
safety	['IEC 62619', 'IEC 63056', 'IEC 62477', 'IEC 62040']

Warranty & service

conditions	per Sungrow warranty letter
cycle_life	—
design_life_years	—
extended_options_years	[]
field_replaceable_parts	['PACK (battery module)', 'switch gear', 'base']
note	Datasheet V4 row 'Warranty: 10 Years'
standard_years	10
throughput_guarantee_mwh	—
years	10

Packaging & logistics

gross_weight_kg	—
transport_restrictions	UNKNOWN - UN38.3 and Class 9 are not explicitly printed in the fetched datasheet or user manual

Документи

compatibility-list Compatibility List PUBLIC 2026 | Version 4.3 rev V4.3

compatibility-list Sungrow SBR and SBH Cross Reference Chart V2.4 rev V2.4

datasheet SBH100/150/200/250/300/350/400 Datasheet V4 EN rev V4

product-page Sungrow SBH product page rev UNKNOWN

user-manual High Voltage LFP Battery User Manual (SBH series) rev UNKNOWN

Зафіксовані конфлікти

compatibility: SBH with SH5.0/10RT Review required

None — value currently stored in ANMA

Compatibility List V4.3 (01.06.2026) lists SBH150-400 with 'SH5.0/10RT V112 and -20'; Compatibility List V3.3 (26.05.2025) lists SH5.0/10RT as 'NO' for SBH100-400 — https://info-support.sungrowpower.com/market-material/41ab25da-0bbb-451b-8a51-fd4abd3be0bd.pdf

interfaces.can Review required

yes - two ports, 'IN is used for connecting the termination resistor, while OUT for the hybrid inverter' — stored value

True — incoming package